• Online only
single-mass flywheel kit reinforced alpha 147 - gt Steel flywheel kit with reinforced clutch

single-mass flywheel kit reinforced alpha 147 - gt

€1,047.00
Tax included Solitamente 24 ore

Kit with single-mass flywheel steel, made to accommodate a specific disk with springs and thrust complete with crown.

Quantity
  Usually ships in 24 hours
Remember ! You find it on Protoxide Only!

Total Rating Total Rating:

0 1 2 3 4
5,00/5 - 2 reviews

View ratings
0 1 2 3 4 2
0 1 2 3 0 0
0 1 2 0 1 0
0 1 0 1 2 0
0 0 1 2 3 0

  Add Review View Reviews View Reviews
Pinterest
 

SECURE ENCRYPTED PAYMENTS

 

TRACKING NUMBER FOR ALL ORDERS

 

MON-FRIDAY SUPPORT 10.00-12.30 15.00-17.30

  • There are known problems of breakage of the dual mass flywheel when increasing the number of horses (even if only by reprogramming the control unit).
  • Steel flywheel complete with crown for the starter
  • disc brake pad (not copper) PROTOXIDE with battery reinforced with 3 dampers specifically designed to reduce vibration and "loaded "to the contrary.
  • crankshaft bolts specific for this application including
  • Original reinforced pressure plate
  • The weight of the whole assembly is about 16kg.
  • It can be installed on many models including Alfa 147, Alfa GT
  • This kit eliminates the problems present in acceleration even at low engine speeds, especially in the higher gears, caused by the failure of the "dual-mass flywheel original" thus eliminating slipping clutch or flywheel, pressure plate reinforced for about one and a disc brake padPROTOXIDE only unobtainable 
  • E 'need to use the original thrust bearing to be purchased at the dealer because they do not understand.
  • PROTOXIDE assumes no liability due to a non-compliant application choice for your car, although you can always replace it with the correct type without additional expense, and in any case every order received, you will be contacted by one of our technicians Checking forand with you the correct model for your application.
  • Protoxide assumes no responsibility for any vibrations that can occur during normal operation of the engine, due to the removal of the original dual-mass flywheel, as our products are suitable only for racing vehicles where the only prerogative are the major performance at the expense of everything else,Noise, comfort and durability(Especially when an application involves the use of copper material).
Name Value

Reviews Reviews (2)

Based on 2 reviews - 0 1 2 3 4 5,00/5
Sort by:

0 1 2 3 4
(5/5

verona 11/03/2012

2 of 2 people found the following review helpful

ho montato questo kit per poter reggere la coppia del motore dopo alcuni interventi elettronici e meccanici.la frizione regge benissimo lo sforzo il volano essendo poco più leggero dell'originale aiuta a salire di giri rapidamente senza compromettere troppo la coppia.la rumorosità è rimasta buona.si nota un pò di vibrazione quando si affonda a pieno l'accelerato in piena coppia.ma il motore vibra meno sia al minimo sia al momento dell'accensione!nel complesso il kit è ottimo.anche nel prezzo.realizzato molto bene.completo di tutto.tranne il cuscinetto reggispinta.che consiglio di cambiare quando si interviene.il servizio e la serietà dell'azzienda sono ottimi.consegna rapidissima e un ufficio tecnico all'avanguardia.


0 1 2 3 4
(5/5
2 of 2 people found the following review helpful

Montato su alfa 147 jtd 115hp finalmente il pedale morbido come su questa motorizzazione non è mai stato. ed è sparito anche quel classico scalino che si forma nella corsa del pedale a volte anche dopo poche migliaia di chilometri. a differenza di ciò che si legge in giro non avverto nessuna particolare vibrazione ne sulla leva del cambio e tantomeno sul pedale. anche al minimo non si ci accorge di differenze se non per il differente rumore che provvoca. l unico modo per trovare una vibrazione e mettere il motore sottocoppia con una marcia alta ed affondare l acceleratore. allora vibra di piu del bimassa originale. ma essendo questa una condotta di guida ovviamente errata è un problema che non dovrebbe sussistere mai. ha la comodita di montaggio del kit ricambio originale cosi neppure i meccanici avranno da lamentarsi non dovendo modificare nulla e neppure dissaldare la corona dall originale per essere montata su questo in acciaio quindi che dire. ho 41kg di coppia. e anche la frizione regge perfettamente e direi pure con grossi margini di sicurezza. lo consiglio a chi non piace avere problemi! in conclusione ottimo prodotto