This kit is equipped with a single-mass flywheel in steel, a super-reinforced pressure plate and a clutch with a ferrule disc (not in copper).
Engine code cff - cffb
Couple max. 59kgm
It is necessary to use the original thrust bearing to be purchased in the dealership as it is not included.
ProtoXide assumes no responsibility due to an improper choice of the application for your car, even if you can always replace it with the correct type without further costs, and in any case with each order received, one of our technicians will contact you to check with you the correct model for your application.
Protoxide assumes no responsibility for any vibrations that may occur during normal engine operation, due to the removal of the original bi-mass flywheel, as our products are only indicated for competition vehicles where the only prerogatives are the greatest performances to the detriment of all the rest, noise, comfort and durability (especially when an application involves the use of copper material).
Total weight kg.
It is installed on the whole seat audi and vw group with 2 and 4-wheel drive.
Volkswagen Scirocco 2000 140hp Turbodiesel racing single-mass flywheel kit complete with reinforced Sasch Performance pressure plate, different version with more load than the reinforced Sasch performance for this model and ferodo clutch disc with copper braids in the ProtoXide compound.
Kit with steel flywheel Renault Clio 3 RS3 200 hp - 203hp R3 F4r830 in steel with reinforced single-disc copper clutch with Ergal bell for SADEV GEARBOX (not suitable for other applications with original gearbox), which allows you to have a super lightened clutch assembly all machined from solid, with 60-2 tone wheel for reading with sensor for original control unit and racing control units and relative crown for starter motor included.
Steel single-mass flywheel kit with clutch specific to Alfa 159 2000 - Fiat Croma 1900 16v JTDM 150 hp and 200 hp engine code 939B3000 125 KW with F40 gearbox transmission. This is a model used exclusively for this specific application which as standard uses an original dual mass flywheel 55214811 with F40 transmission with a wear recovery pressure plate, while our application allows you to remove the wear recovery system using a traditional system but which allows to maintain a torque of 59kgm!
Lightweight single-mass steel flywheel complete with reinforced single-disc clutch with reinforced push-type pressure plate for all Alfa Giulia 2200 turbodiesel engines with manual gearbox, super-reinforced pressure plate with no wear recovery and clutch disc with reinforced springs dedicated for this application!
Fiat Panda 100 HP Flywheel Kit with reinforced clutch with lightened steel flywheel with reinforced copper clutch with bell machined from solid. It can be used in all applications with Fire engines that use clutches up to a maximum of 200mm.
Flywheel kit in special single-mass steel with clutch with copper disc and reinforced push type pressure plate. Can be installed on Doblo, Marea, Bravo, Multipla, Grande Punto with 1.9 8v JTD engines for applications up to and over 300 hp
Flywheel kit in lightened steel with copper-reinforced clutch with pressure plate bell machined from solid, with Renault tone wheel for reading with sensor for the original control unit and competition control units.
Kit with flywheel in super lightened steel with reinforced clutch in copper with bell machined from solid, with phonic wheel 60-2 for reading with sensor for original control unit and competition control units.
Flywheel and clutch kit reinforced with single-mass flywheel in lightened steel, specific for Fiat Alfa Lancia cars such as Giulietta 1.6 Mjet, 1600 MJET 105hp ALFA ROMEO Giulietta, Fiat BRAVO 2 etc. 88kw
Online only
Kit with single-mass flywheel made to accommodate a specific disc with thrust springs with double shock absorber.
This website uses cookies to ensure you get the best experience on our websiteAbout cookies